How Much Carpet Does a Car Floor Need? Measuring Footwells, Tunnel and Boot
A car floor is not flat and it is not a rectangle, which is why people either guess the carpet they need or buy a whole roll to be safe. Neither is necessary. If you treat the floor as a handful of rough rectangles, measure each one along the surface rather than in a straight line, and add an allowance for trimming, you get a figure that is close enough to order from. The Carpet Area Calculator does the adding up: you enter each section's length and width in metres, set a trim allowance, and it returns the measured area, the area with allowance and the same figure in square feet.
How to split the floor into sections
Take the seats out of the picture first. On most cars the carpet runs under the front seats, so even if you leave the seats in place for measuring, the carpet you buy has to cover that area. The usual sections are:
- Driver and passenger footwells. Measure from the point where the carpet meets the bulkhead (the toe board, often well up behind the pedals) down and back to the front edge of the seat runners.
- The transmission tunnel. Lay the tape over the tunnel from one side, across the top and down the other side. That unfolded width is what the carpet has to span, and it is often double the tunnel's apparent width.
- Under the front seats. Side to side across the car, from the back of the footwells to the rear seat kick panel.
- Rear footwells. Across the car, from the front seat area to the base of the rear seat, including any rise up the seat base.
- The boot floor, if you are doing it. Many floor carpet sets leave it out, because the boot often has its own board with a separate covering.
Measure along the surface with a tailor's tape or a length of string laid into the shape, not with a steel rule held across the gap. A footwell that is 60 cm across at the top can be 85 cm long once you follow the floor down and up the bulkhead. Round each measurement up to the next 5 cm. That is not the trim allowance, it is just honest measuring.
Worked example: a compact hatchback
Here is a typical small front-wheel-drive hatchback, measured section by section. The tunnel is low on a car like this, but its unfolded width still adds up.
| Section | Length × width (m) | Area (m²) |
|---|---|---|
| Driver footwell | 0.85 × 0.60 | 0.51 |
| Passenger footwell | 0.85 × 0.60 | 0.51 |
| Tunnel, unfolded | 1.10 × 0.40 | 0.44 |
| Under the front seats | 0.50 × 1.20 | 0.6 |
| Rear footwells | 0.55 × 1.30 | 0.715 |
Entered into the calculator with the default 10% trim allowance, that floor measures 2.78 m² and the carpet to buy is 3.05 m², or 32.9 ft². Add the boot floor at 0.75 × 1.00 m (0.75 m²) and the measured area becomes 3.53 m², or 3.88 m² with the same allowance.
Those figures are worth a sanity check against the car. A small hatchback's cabin floor is roughly the size of a single bed, so an answer between two and a half and three and a half square metres is believable. If you get eight, you have probably measured something twice or entered centimetres as metres.
Choosing the trim allowance
Carpet is cut oversize and trimmed back to the edges of the floor pan, the sill plates and the seat mountings. How much extra you need depends on how you are buying it.
| Trim allowance | Hatchback carpet (m²) | In ft² | When it fits |
|---|---|---|---|
| 0% | 2.78 | 29.9 | Checking a moulded set's stated coverage only |
| 10% | 3.05 | 32.9 | Flat pieces, simple floor, careful cutting |
| 15% | 3.19 | 34.4 | A tall tunnel, several darts and seams |
| 20% | 3.33 | 35.8 | First attempt, or a pattern or pile that must run one way |
Pile direction matters more than people expect. Cut-pile carpet looks a different shade depending on which way the pile lies, so every piece in a car should run the same direction, usually with the pile laid towards the rear. That stops you rotating pieces to nest them on the roll, which is why the higher allowances exist.
Worked example: a mid-size SUV
A larger car changes the numbers more than its length suggests, because almost every section grows in both directions and the boot is bigger.
| Section | Length × width (m) | Area (m²) |
|---|---|---|
| Driver footwell | 0.95 × 0.65 | 0.617 |
| Passenger footwell | 0.95 × 0.65 | 0.617 |
| Tunnel, unfolded | 1.30 × 0.55 | 0.715 |
| Under the front seats | 0.55 × 1.35 | 0.743 |
| Rear footwells | 0.65 × 1.40 | 0.91 |
| Boot floor | 1.00 × 1.10 | 1.1 |
That is 4.7 m² measured, about 1.7 times the hatchback's cabin, and 5.41 m² (58.2 ft²) with a 15% allowance for the taller tunnel. If the SUV has a third row, measure that footwell and the floor behind it as two more sections rather than scaling up.
From square metres to a length off the roll
Automotive carpet on the roll is usually sold by the linear metre at a fixed width, often around 2 metres. Dividing the area by the roll width gives the shortest length that could possibly hold it: for the hatchback cabin with a 10% allowance that is 1.53 m of a 2 m roll, and 1.94 m with the boot. The Upholstery Fabric Calculator does this division if you enter the area as one section with your roll width.
Treat that as a floor, not an order. Footwell pieces are long and narrow and the tunnel piece is long and wide, so they rarely nest perfectly across the roll. Make paper or card templates of each piece, lay them out on a chalked rectangle the width of the roll, and measure the length they actually occupy. Then buy that, rounded up to whatever step the supplier sells in.
What the calculator does not cover
- Shape. It adds rectangles. Wheel arches, curves up the bulkhead and the corners around seat mountings are inside the trim allowance, not modelled.
- Moulded carpet. A moulded set is pressed to the floor shape and sold per car, not per square metre. The area tells you how much a set should cover; it does not price one.
- Underlay and insulation. Jute or foam underlay, and any sound deadening under it, are separate purchases with their own areas. The guide to sound deadening for doors and floor works through that layer.
- Roll layout. As above, area divided by width is a minimum.
- Fit around fixings. It cannot tell you where the holes go.
Safety: what must stay clear
A floor covering is part of how the car is driven and how its occupants are restrained, so a few rules are not optional:
- Nothing may reach the pedals. New carpet plus new underlay can sit higher than the old floor; check that the accelerator, brake and clutch travel fully with the seat in every position. Floor mats should be the right ones for the car, fixed on the factory retention clips, and never stacked one on top of another, which is a known cause of trapped pedals.
- Keep the anchors and runners clear. Cut carpet around seat-belt anchors, seat runners and the ISOFIX/LATCH child-seat anchor points, never over them, so each one seats metal to metal. Refit seat and belt anchor bolts to the torque in the service manual.
- Airbag and pretensioner wiring. Taking the seats out to lay carpet means unplugging seat airbag, belt pretensioner and occupancy-sensor connectors. Disconnect the battery and wait as long as the service manual says before you unplug anything, or have the seats removed and refitted by a professional.
- Adhesive and materials. Contact and spray adhesive give off flammable solvent vapour. Work with the doors open and strong ventilation, wear a respirator with organic-vapour cartridges, gloves and eye protection, and read the product's Safety Data Sheet. Buy carpet sold for vehicle interiors, which should meet the interior flammability standard (FMVSS 302 in the US, or the local equivalent); household carpet is not tested to it.
Once you have the area, the re-trim budgeting guide turns it, and the underlay and adhesive that go with it, into a shopping list.