VEHICLEINTERIOR
← The Journal
· The VehicleInterior Team

How Much Fabric Do You Need to Replace a Sagging Headliner?

A sagging headliner is almost never a fabric problem. The thin foam layer that bonds the fabric to the roof board breaks down with heat and age, turns to a sticky orange powder, and the fabric lets go. Gluing the old fabric back up does not last, because there is nothing left for the glue to hold. The fix is to take the board out, scrape it clean and cover it with new foam-backed headliner fabric. This guide works out how much fabric to buy, using the Upholstery Fabric Calculator, and how many cans of adhesive, using the Material Cost Estimator.

Before you start: the roof is an airbag zone

Many cars have curtain airbags folded along the roof rails, right at the edges of the headliner, and the trim on the A, B and C pillars covers or guides them. Getting the board out means removing those pillar trims, the grab handles, sun visors, the interior light and often a roof console with wiring.

  • Disconnect the battery and wait as long as the service manual specifies before unplugging anything near an airbag.
  • Follow the manual for pillar trims: some use special clips or tethers that are designed to hold the trim during airbag deployment and must be replaced, not reused.
  • Never glue fabric, foam or anything else over an airbag cover or onto the curtain airbag itself, and do not let new fabric wrap so far that it bridges the gap the airbag deploys through.
  • If any of this is unclear for your car, have a trimmer or a garage remove and refit the board. You can still do the re-covering on the bench.

Why the area alone is not enough

The fabric calculator works the way upholstery is usually bought: it adds the area of the panels, adds a waste allowance and divides by the roll width to give a length. That is right for seats, which are cut from many small pieces. A headliner is different: it is one large piece with no seams, wrapped a few centimetres past the edge of the board on every side. So two figures matter, and you buy the larger:

  1. The area figure from the calculator: board area plus allowance, divided by the roll width.
  2. The one-piece figure: the board's length plus the wrap at each end. This only works if the board's width plus the wrap at each side also fits within the roll width.

Foam-backed headliner fabric is commonly sold on rolls about 1.52 m (60 inches) wide. The examples below use that width, a 15% allowance, and 5 cm of wrap on each edge.

Three boards worked through

Measure the board once it is out of the car, along its surface (it is curved), front to back for the length and side to side for the width.

BoardLength × width (m)Area (m²)Calculator length (m)One-piece length (m)Width needed (m)Fits a 1.52 m roll?
Small hatchback1.3 × 1.351.761.331.41.45yes
Saloon1.5 × 1.42.11.591.61.5yes
Estate or SUV2.05 × 1.452.972.252.151.55no

For the hatchback, the calculator's 1.33 m (1.45 yd) is a little shorter than the 1.4 m a single piece needs, so the one-piece figure wins. The saloon is similar. Either way, the length to buy is set by the board, and the area figure is a check that you have not forgotten a piece.

The SUV board is the useful warning. Its width plus wrap is 1.55 m, more than the 1.52 m roll, and turning the fabric round does not help because the board is even longer. The options are a wider roll (some suppliers stock one), a smaller wrap if the board's edges are hidden under trim anyway, or a supplier's pre-cut headliner kit for that model. Find this out before ordering, not with the board on the bench and the glue open.

A sunroof opening reduces the area but not the piece: on the hatchback, cutting out a 0.80 × 0.45 m opening (0.36 m²) brings the calculator figure down to 1.06 m, yet you still need one piece the full length of the board, because the opening is cut after the fabric is laid.

Adhesive

Use a high-temperature spray adhesive sold for headliners. A roof gets very hot in summer sun, and general-purpose spray glue softens and lets go. The adhesive goes on both surfaces, the clean board and the back of the fabric, so the area to spray is twice the board area. Here the cans are assumed to cover 1.8 m² each, which is a planning figure: check the coverage on the can you buy, because it varies with the product and how heavily you spray.

What it costs in materials

With planning prices of 22.00 per metre of fabric (bought in whole metres) and 14.00 per can, replace both with your supplier's current price:

BoardFabric to buyFabric costSpray area (m²)CansAdhesive costTotal
Small hatchback2 m44.003.51228.0072.00
Saloon2 m44.004.2342.0086.00
Estate or SUV3 m66.005.94456.00122.00

The fabric lines are whole metres because that is how the estimator rounds. If your supplier sells by the half metre or the yard, enter the price and coverage for that step instead and the count will come down. The spare from the hatchback's second metre is useful: covering the sun visors or a pillar trim in the same fabric keeps the color matched.

What the calculators cannot tell you

  • Whether the board is sound. A board that has gone soft, cracked or warped from water needs repair or replacement first. Fabric will not hide it.
  • Scraping the old foam off. This is the slow part. Every trace of the old crumbled foam has to come off, or the new fabric will fail the same way.
  • Pattern and nap. Most headliner fabric is plain, but if yours has a direction, the piece must run front to back, which fixes the orientation.
  • Clips, tools and labour. Trim clips often break; buy a bag. Professional removal near airbags is a cost worth budgeting.

Working safely with headliner adhesive

  • Spray adhesive is flammable and its solvent vapour builds up fast. Spray outdoors or in a well-ventilated space, away from any flame, heater or spark, and wear a respirator with organic-vapour cartridges, gloves and eye protection. Read the Safety Data Sheet before you open the can.
  • Let the board air off for the time the can specifies before it goes back into the car, so solvent is not trapped in the cabin.
  • Buy fabric sold for vehicle headliners, which should meet the vehicle-interior flammability standard (FMVSS 302 in the US, or the local equivalent). Furnishing fabric is not tested to it.

If the headliner is one job in a bigger refresh, the re-trim budgeting guide puts it alongside carpet and seats.

Get new guides by emailOccasional emails. No spam. Unsubscribe anytime.