VEHICLEINTERIOR
← The Journal
· The VehicleInterior Team

How to Size Replacement Foam for a Car Seat

A seat that has gone flat, sags to one side when you get in, or lets you feel the frame through the cushion has worn-out foam, and new covers on old foam just look like a new cover on a flat seat. Replacing the foam is often the part of a re-trim that makes the biggest difference to comfort. It is also easy to under-order, because foam is sold in blocks and sheets with a thickness, while a seat cushion is a shaped, tapering object. This guide uses the Seat Foam Calculator to turn measurements into the volume to buy.

What the calculator works out

The calculator treats each piece of foam as a rectangular block: length times width times thickness. It reports the volume in cubic metres and in board-feet, the unit many foam sellers in the US price by (one board-foot is a piece 12 by 12 by 1 inches). Enter a density and it also gives the mass of the block.

The default example, a 50 × 50 cm cushion 10 cm thick at 35 kg/m³, comes to 0.025 m³, which is 10.59 board-feet and 0.88 kg. That is a useful sanity figure: one ordinary seat cushion is roughly ten board-feet.

Break the seat into blocks

With the cover off, the foam usually comes apart into a few pieces, or at least shows where it was built up. A typical front bucket seat breaks down like this:

PieceBlock (cm)QtyVolume each (m³)Board-feet eachMass each at 35 kg/m³
Seat cushion50 × 48 × 1010.02410.170.84 kg
Backrest60 × 42 × 610.01516.410.53 kg
Cushion bolster50 × 12 × 820.00482.030.17 kg
Backrest bolster60 × 12 × 620.00431.830.15 kg

Run each block through the calculator and add them, counting the bolsters twice. One seat totals 0.0573 m³, or 24.3 board-feet, and weighs 2.01 kg at 35 kg/m³. A pair of front seats is 48.6 board-feet and 4.02 kg. Those masses are small, which is the point: if a supplier's quote implies a very different weight for that volume, the density is not what you think it is (see what foam density for a car seat cushion).

Measure the thickest point, not the average

Real cushions taper. A typical seat cushion is thicker at the front edge, where your thighs rest, than at the back, where it meets the backrest. You cannot buy a tapered block; you buy a block as thick as the thickest point and carve the shape out of it.

Take a cushion that runs from 10 cm at the front to 7 cm at the back. The block you need is 10 cm thick: 10.17 board-feet. A block at the average thickness of 8.5 cm would be 8.65 board-feet, and it would be too thin at the front. The 1.52 board-feet difference ends up as offcut, and that is fine. Order by the bounding block, and use the offcuts for bolster build-ups.

Cut slightly oversize

Trimmers usually cut foam a little larger than the cover, so the cover is filled tight and does not wrinkle as the foam settles. Adding 1 cm to the length and width of the cushion block (51 × 49 instead of 50 × 48) takes it to 0.025 m³, about 4.2% more foam. It is a small amount on the order, and it is the difference between a cover that looks stretched and one that looks loose. How much oversize suits your cover depends on its material: vinyl and leather stretch less than cloth.

Sheets versus cut pieces

Foam is sold either cut to size or as full sheets. A 2 m × 1 m sheet 10 cm thick is 84.76 board-feet and weighs 7 kg at 35 kg/m³, about 3.5 times the volume one seat needs. A sheet can work out cheaper per board-foot, but only if you have the thicknesses you need from it. Most seats use at least two thicknesses (here 10, 8 and 6 cm), so a single sheet rarely covers a whole seat neatly. Price the cut pieces against the sheets you would need, not just the sheet price.

Measuring tips

  • Measure the old foam with the cover off and the seat unloaded. Foam that has collapsed reads thinner than it was new, so where it is crushed, measure the uncrushed edge or take the thickness from the other seat.
  • Keep the old pieces until the new ones are cut. They are the best template you have for the contours.
  • Note which way the cushion slopes and where the listing channels run before you pull anything apart, and photograph each layer.
  • Write every block down as length × width × thickness in the same units, so it can go straight into the calculator.

What the calculator does not cover

  • Shape. The tool calculates rectangular blocks. It does not model contours, channels for listing wires, or the sculpted bolsters of a sports seat. Order by the bounding block and carve.
  • Firmness. Density predicts how durable foam is and what it weighs, but not how firm it feels. Firmness is a separate rating (indentation force, given as ILD, IFD or hardness in newtons). Ask for both.
  • Moulded seats. Many modern seats use a single moulded foam with frame inserts and heating elements built in. Replacing those is usually a matter of buying the moulded part, not cutting blocks.
  • Scrim foam on the cover. The thin foam laminated to the back of the cover is part of the cover material, not the seat foam.

Safety: airbags, connectors, adhesive and flammability

  • Getting at the foam means removing the seat and the cover. Front seats often contain a side airbag in the backrest that deploys through a tear seam in the cover. Do not move, pad over, glue onto or obstruct the airbag module, refit any cover with its airbag seam exactly where it was, and if the backrest has an SRS tag, leave the backrest work to a professional who follows the manufacturer's procedure.
  • Seat removal means unplugging airbag, seat-belt pretensioner and occupant-sensor connectors. Disconnect the battery and wait for the time the service manual specifies, follow the manual for refitting and bolt torques, or have a professional remove the seats. A seat heater element or occupant sensor mat in the cushion must go back exactly as it came out.
  • Foam is usually bonded with spray adhesive. Work outdoors or with strong ventilation, wear a respirator with organic-vapour cartridges, gloves and eye protection, and read the Safety Data Sheet.
  • Buy foam that meets FMVSS 302 (US) or your local equivalent for vehicle interiors. Furniture foam from a craft shop is not necessarily tested to it, and the difference only matters in a fire.

Measure each block at its largest, run them through the Seat Foam Calculator, add a centimetre for a tight fit, and ask the supplier for density, firmness and the flammability rating together.

Get new guides by emailOccasional emails. No spam. Unsubscribe anytime.