VEHICLEINTERIOR
← The Journal
· The VehicleInterior Team

Leather, Vinyl or Fabric: What Does a Front Seat Re-trim Cost in Each?

Choosing a seat material usually starts with looks and ends with a price, and the price people compare is the wrong one. A price per metre of vinyl and a price per square foot of leather cannot be compared directly, because the two are bought in different units with very different waste. The useful comparison is the total for the same pair of seats. This guide works that out for cloth, vinyl, leather and a mixed trim, using the Upholstery Fabric Calculator for quantities and the Material Cost Estimator for whole units and totals.

All prices below are example figures chosen to make the arithmetic visible. They are not quotes and they will not match your supplier. Replace them with current prices for the material you are actually looking at; the method is the point.

The seats

The example is a pair of front bucket seats measured panel by panel: 3.2 m² of panels in total. How to measure them is covered in how much upholstery fabric to re-cover two front seats. The same panel list is used for every material, so the only things that change are the waste allowance and the way the material is sold.

Cloth and vinyl: bought by the metre

With a 20% waste allowance and a 1.4 m roll, the calculator gives 2.75 m. Suppliers cut whole metres, so in the cost estimator enter 2.75 as the area, 1 as the coverage per unit, and the price per metre. It rounds up to 3 m.

  • Automotive cloth at an example 22.00 per metre: 3 m costs 66.00.
  • Automotive vinyl at an example 30.00 per metre: 3 m costs 90.00.

Note that cloth with a pile or a pattern may need a bigger allowance than plain vinyl, which can push it into another whole metre. Run both allowances before deciding.

Leather: bought by the hide

Leather needs a much higher allowance because hides are irregular, the belly is thin and marks must be cut around. At 50% waste the seats need 51.7 ft². In the cost estimator, enter 51.7 as the area, 50 as the coverage per unit (one average 50 ft² hide), and the price per hide. It rounds up to 2 hides.

  • Leather at an example 320.00 per hide: 2 hides cost 640.00.

The upholstery calculator's own hide count for the same inputs agrees, which is a useful cross-check: if the two ever disagree, one of the inputs is in the wrong unit. Why the allowance is so high, and why the hide size you are sold matters, is explained in how many leather hides a car interior needs.

Leather faces, vinyl everywhere else

Many factory "leather" seats are leather only where you sit: the cushion and backrest inserts. Bolsters, sides and backs are matched vinyl. That mix is worth pricing because it changes how the hide is used.

  • The four inserts total 0.98 m². At 50% waste that is 15.9 ft², which is 1 hide.
  • The remaining panels in vinyl at 20% waste need 1.9 m, rounded up to 2 m, which is 60.00 at the example price.
  • Together: 380.00.

The inserts use only a fraction of a hide, and you still pay for the whole one. That is the honest weakness of a mixed trim on just two seats: the leftover leather is only good value if you use it, for example on door-card inserts or an armrest lid.

The totals side by side

MaterialWaste allowedBought asExample total
Cloth20%3 m66.00
Vinyl20%3 m90.00
Leather inserts, vinyl elsewhere50% / 20%1 hide + 2 m380.00
Full leather50%2 hides640.00

Whatever prices you use, the shape of the table tends to hold: cloth and vinyl are close to each other, and leather is a step up mainly because of how much of each hide you cannot use. Each of these totals is a planning figure: confirm current prices, minimum cut lengths and delivery before you rely on one.

The extras every option needs

The covering material is the largest line, but not the only one. Covers are normally bonded to a thin scrim foam, and loose foam is re-glued to the frame, both with spray adhesive. If one can covers about 2 m² (check the can; coverage varies a lot with how heavily you spray), the 3.2 m² of panels needs 2 cans, or 28.00 at an example 14.00 each. Add thread rated for upholstery and UV, hog rings or clips, and any replacement foam. Collapsed cushions are common on older seats; sizing new foam is covered in how to size replacement seat foam.

What the cost estimate does not cover

  • Labour. The calculators price material only. If a trimmer sews the covers, labour will usually be the larger part of the bill, and it hardly changes between cloth and vinyl.
  • Wear and care. Vinyl wipes clean and tolerates sun, but gets hot and can crack with age. Cloth breathes but stains. Leather needs cleaning and conditioning, and cheap leather can crack faster than good vinyl. A higher price does not guarantee a longer life.
  • Nesting. Metres are calculated from area, which assumes panels pack perfectly. Lay out paper patterns on a strip the width of the roll before ordering.
  • Exchange rates, shipping and minimum orders. All change the real cost and none are in the formula.

Running the comparison for your own seats

  1. Measure every panel of one seat and enter the areas in the Upholstery Fabric Calculator, doubled for the pair.
  2. Run it at 20% waste for cloth and vinyl and note the metres; run it again at 40% and 50% for leather and note the square feet.
  3. Get one current price per metre for each cloth and vinyl you like, and the price and average size of the hides a leather supplier has in stock.
  4. In the Material Cost Estimator, enter metres with a coverage of 1, and square feet with a coverage equal to the hide size.
  5. Add adhesive, thread and foam to every row, then compare totals rather than unit prices.

Safety applies whatever you choose

  • Front seats often have a side airbag in the backrest that bursts out through a tear seam. Any replacement cover, in any material, must be made as airbag-compatible for that seat with the specified tear stitching, or the airbag may not deploy. Never cover, glue over or obstruct an airbag module.
  • Taking seats out means disconnecting airbag, pretensioner and sensor connectors. Disconnect the battery and wait as the service manual specifies, follow the manual, or have a professional remove and refit the seats.
  • Spray and contact adhesives give off flammable organic vapour: work with good ventilation and wear a respirator with organic-vapour cartridges, gloves and eye protection. Read the Safety Data Sheet first.
  • Whichever material you pick, ask for confirmation it meets FMVSS 302 (US) or your local equivalent for vehicle interiors. Furniture fabric and foam are not automatically tested to it.
Get new guides by emailOccasional emails. No spam. Unsubscribe anytime.