VEHICLEINTERIOR
← The Journal
· The VehicleInterior Team

How Much Upholstery Fabric Do You Need to Re-cover Two Front Seats?

The question every seat re-trim starts with is how much material to order, and the answer you get from a forum ("about five yards", "three metres should do") is usually right for somebody else's car. A better answer takes twenty minutes with a tape measure. You break each seat into the flat panels it is sewn from, measure each one as a rectangle, add them up, and convert that area into the length of material to buy at your roll width. The Upholstery Fabric Calculator does the adding and converting; this guide shows what to measure and how to read the result.

Measure the panels, not the seat

A seat cover is not one piece of cloth. It is a set of panels sewn together: a centre insert on the cushion and on the backrest, raised bolsters either side, narrow boxing strips that make the sides, a rear panel on the back of the backrest, and a headrest cover. If you can take the old cover off, unpick one seam and you will see the shapes. If you cannot, measure on the seat, following each seam line, and take the widest and longest point of every panel.

Measure each panel as the rectangle that would contain it. A curved bolster still has to be cut from a rectangle of material, so the bounding rectangle is the honest figure. Measure over the curve with a soft tape, not straight across with a rule, or the cushion bolsters will come out short.

Here is a typical front bucket seat measured that way. The dimensions are an example; yours will differ, which is why you measure.

PanelSize (cm)How manyArea (m²)
Cushion insert50 × 4810.24
Cushion side bolsters50 × 1520.15
Cushion front apron50 × 1210.06
Cushion side skirts50 × 1220.12
Backrest insert60 × 4210.252
Backrest side bolsters60 × 1420.168
Backrest rear panel70 × 5010.35
Backrest side boxing70 × 820.112
Headrest (front and back)30 × 2520.15

The areas in the last column already include the count, so the two cushion bolsters together are 0.15 m². One seat totals 1.6 m², and the pair is 3.2 m². That sits in the range you would expect for ordinary front buckets. Sports seats with tall bolsters and integrated headrests come out larger; flat bench-style fronts in older cars come out smaller.

Enter it and choose a waste allowance

Type each panel area into the calculator as its own section (or enter one seat's total twice), set the roll width, and choose a waste allowance. Automotive vinyl and cloth are commonly sold about 1.37 to 1.4 m wide, so 1.4 m is used here.

The waste allowance is where judgment comes in. It has to cover the seam allowance around every panel (roughly a centimetre each side), the gaps between curved pieces laid on a straight roll, and any pattern or pile that forces all panels to face the same way. Fifteen percent is a fair minimum for a plain vinyl; thirty percent is safer for cloth with a nap, a stripe that must line up across the seat, or a first attempt.

Waste allowanceArea with wasteLength at 1.4 m wideIn yards
15%3.68 m²2.63 m2.88 yd
30%4.17 m²2.98 m3.25 yd

Roll width matters more than people expect. At 30% waste, the same pair of seats needs 3.04 m of a 1.37 m roll and 3.47 m of a 1.2 m roll. If your supplier quotes a width "including selvedge", subtract the selvedge: only the usable width counts.

Turn metres into an order

Suppliers sell by the whole metre or yard, so the length has to be rounded up. The Material Cost Estimator does that: enter the length as the area to cover, 1 as the coverage per unit, and the price per metre. Using 30.00 per metre purely as an example (replace it with your supplier's current price):

  • At 15% waste: 2.63 m rounds up to 3 m, a total of 90.00.
  • At 30% waste: 2.98 m also rounds up to 3 m, a total of 90.00.

The difference between the cautious and the optimistic allowance is 0.00 here, because both land inside the same whole metre. That is common, and it is the reason to plan with the generous allowance: it often costs nothing extra, and running out halfway through a backrest costs a second delivery and possibly a dye-lot mismatch. Treat any total as a planning figure until you have checked the current price and the minimum cut length.

If you later decide to do the rear bench to match, measure it the same way. A typical bench cushion and backrest add about 1.78 m², which takes the 30% figure for the whole set to 4.63 m. Buying it all in one order keeps the color from a single batch.

What the calculator does not cover

  • Nesting. The length is area divided by roll width, which assumes the panels could be packed together with no gaps. Real panels cannot be, especially long ones like the 70 cm backrest rear. Before ordering, chalk a 1.4 m wide strip on the floor and lay out paper patterns in it. If the layout needs more length than the calculator says, trust the layout.
  • Hidden parts. Many seats have listings (fabric strips that hold the cover down into the foam channels) and pull-down flaps sewn to the cover. They are often cut from cheaper material, but they still need buying.
  • Foam, scrim and thread. Covers are usually laminated to a thin scrim foam before sewing, and worn seat foam often needs rebuilding. See how to size replacement seat foam.
  • Leather. Leather is sold by the hide, not by the metre. The same calculator reports hides as well; how many leather hides a car interior needs explains why the waste allowance for hides is much higher.

Safety before you take the seats out

Re-covering a seat almost always means removing it from the car, and modern front seats are not just furniture.

  • Side airbags. Many front seats have a side airbag inside the outer edge of the backrest. It deploys by bursting through a deliberately weak tear seam in the cover. A replacement cover must reproduce that seam exactly as the seat maker specifies, with the correct thread and stitch, or the airbag may not deploy properly. Never glue, staple or sew anything over an airbag module, and never use a cover that is not made as airbag-compatible for that seat. If your seat has an "SRS" or "airbag" tag on its side, the backrest cover is a job for a trimmer who works to the manufacturer's procedure.
  • Connectors under the seat. Seat removal means unplugging airbag, seat-belt pretensioner and occupant-sensor connectors. Disconnect the battery and wait as long as the service manual says before unplugging anything, follow the manual for refitting and bolt torques, or have a professional remove and refit the seats. An airbag warning light after refitting must be diagnosed, not ignored.
  • Adhesives. Spray and contact adhesives used to bond scrim foam give off flammable solvent vapour. Work outdoors or with strong ventilation, wear a respirator with organic-vapour cartridges, gloves and eye protection, and read the product's Safety Data Sheet.
  • Flammability. Material for a vehicle interior should meet FMVSS 302 in the US, or the equivalent where you live. Furniture fabric is not necessarily tested to it, so ask the supplier for the rating.

A short checklist

  1. Measure every panel of one seat as a rectangle, following the seams, over the curves.
  2. Enter the areas, your usable roll width and a 30% allowance in the Upholstery Fabric Calculator.
  3. Double for the pair, then check the length against a paper layout on the floor.
  4. Round up to whole metres in the Material Cost Estimator and confirm the price before ordering.
  5. Check the seats for airbag tags before deciding what you will do yourself.
Get new guides by emailOccasional emails. No spam. Unsubscribe anytime.