VEHICLEINTERIOR
← The Journal
· The VehicleInterior Team

Clean or Replace? Deciding What to Do With Stained or Soaked Car Carpet

Car carpet gets a hard life: wet shoes, salt, spilled coffee, the occasional leak. When it looks bad, the choice is between a thorough clean and new carpet, and the cost gap between the two is large enough that it is worth deciding properly. This guide sets out how to tell which one you need, then prices both routes for the same car using the Carpet Area Calculator for the floor area and the Material Cost Estimator for the quantities to buy.

First, find out what kind of dirty it is

Lift a corner of the carpet where it meets a sill or the seat runners and look underneath. What you find there decides most of the question.

Usually cleanable

  • Surface stains from drinks or food that have not soaked through to the underlay.
  • White tide marks from road salt, which come out with warm water and patience.
  • Flattened or matted pile in the heel area, which a brush and steam will lift a little.
  • General grime and odour from use, with a dry underlay and dry floor pan.

Usually needs replacing

  • A wet or damp underlay, or a musty smell that comes back after cleaning. Jute and foam underlay hold water for weeks, and mould grows in them.
  • Rust or standing water on the floor pan. The carpet has to come out anyway so the leak and the metal can be dealt with.
  • Holes worn through at the driver's heel, burns, or a backing that has gone brittle and cracks when bent.
  • Carpet that has shrunk or delaminated after a soaking, so it no longer reaches its edges.

If the carpet is wet, find the leak before deciding anything else. Common sources are blocked scuttle drains under the windscreen, perished door membranes, a sunroof drain tube that has come off, and heater matrix leaks, which leave a sweet smell and a greasy film on the inside of the glass. New carpet over an unfixed leak is money spent twice.

The car in this example

A small saloon, cabin floor only, measured as five rectangles: two footwells of 0.80 × 0.60 m, an unfolded tunnel of 1.00 × 0.45 m, 0.50 × 1.25 m under the front seats and 0.55 × 1.30 m of rear footwells. The calculator gives a measured area of 2.75 m², and 3.16 m² with a 15% trim allowance for cutting new carpet. If you have not measured a floor before, the guide to how much carpet a car floor needs walks through it.

The prices below are round planning figures in no particular currency, there to show the method. Replace each with your supplier's current price before you decide anything.

Route 1: a proper clean

A deep clean with a carpet shampoo and a wet extractor (hired, borrowed or a small spot cleaner) usually means two passes over the whole floor: one to loosen, one to rinse out. Coverage figures are on the bottle; here we assume a bottle that the label says covers 5 m² when diluted, at a planning price of 9.00.

  • Area to cover: 2.75 m² measured, twice over, is 5.5 m². No trim allowance here, because nothing is being cut.
  • The Material Cost Estimator, with 5 as the coverage per unit and 9.00 as the price, gives 2 bottles for 18.00.

Add the extractor hire if you do not own one. Then the part that matters most: dry it. Extract as much water as you can, leave the doors open in dry weather or run the heater with the windows cracked, and press a dry towel into the pile the next day. If the underlay is still damp after two days, the clean has not worked, and you are in Route 2 territory.

Route 2: new roll carpet

Roll carpet sold for car interiors is commonly 2 m wide and priced by the linear metre. In the estimator, that means a coverage of 2 m² per unit (one metre of a 2 m roll), and units come back as whole metres because the tool rounds up to whole units. With a planning price of 30.00 per metre:

ItemCoverage per unitUnitsPlanning cost
Carpet, 2 m roll2 m² per metre2 m60.00
Underlay, 1.5 m roll1.5 m² per metre3 m24.00
Contact adhesive, 1 litre tin3 m² per tin116.00
Total100.00

The carpet line is 3.16 m² divided by 2 m² per metre, which is 1.58 m, rounded up to 2. The underlay assumes a narrower 1.5 m roll, so it needs a metre more. Adhesive is entered for half the floor area, because car carpet is normally glued only where it has to hold a contour (up the tunnel sides and the bulkhead) and left loose on the flat so it can come out again.

On these planning prices the replacement route costs 82.00 more in materials than the clean, before your time. That gap is why the inspection in the first section matters: if the underlay is dry and the floor pan is sound, cleaning is almost always the better spend.

What about a moulded carpet set?

Many cars have a moulded carpet set available, pressed to the floor's shape with the heel pad and openings already in place. It is priced per car, not per square metre, so the estimator cannot price it. What the area figure does let you do is compare: if a moulded set costs about what the roll carpet, underlay and adhesive cost together, the moulded set is usually the better buy, because it saves a day of templating and cutting and it fits like the original.

What this comparison does not cover

  • The cause. Neither tool knows why the carpet is stained or wet. Leaks, rust repair and drying the floor pan come first and cost what they cost.
  • Labour and hire. The estimate is materials only: no extractor hire, no tools, no trim clips that snap when panels come off.
  • Real coverage. A shampoo label's coverage assumes light soiling. Heavy soiling uses more. A carpet roll's usable width is what is left after the selvedge.
  • Odour and mould. If a smell survives a clean and a full dry, the source is usually in the underlay or under the floor, not in the pile.

Safety, whichever route you take

  • Chemicals. Carpet cleaners, solvent spotters and contact adhesive all give off vapour in a small closed space. Ventilate well with the doors open, wear gloves and eye protection, read the Safety Data Sheet, and use a respirator with organic-vapour cartridges for solvent spotters and adhesive. Never mix cleaning products.
  • Electrics under the floor. Some cars have control modules, wiring looms and a passenger seat occupancy sensor at or under floor level. Do not flood the floor, keep water away from connectors, and disconnect the battery and follow the service manual before unplugging anything for seat removal, since seats carry airbag and belt pretensioner connectors.
  • Pedals and mats. Replacement carpet and underlay can sit higher than the old floor. Check the pedals travel fully, use mats made for the car on the factory retention clips, and never lay one mat on top of another.
  • Anchors. Cut new carpet around seat-belt anchors, seat runners and ISOFIX/LATCH points rather than over them, and refit anchor bolts to the service-manual torque.
  • Materials. Buy carpet and underlay sold for vehicle interiors, which should meet the interior flammability standard (FMVSS 302 in the US, or the local equivalent).
Get new guides by emailOccasional emails. No spam. Unsubscribe anytime.