VEHICLEINTERIOR
← The Journal
· The VehicleInterior Team

Sewing Your Own Car Seat Covers: Fabric Yardage and the Airbag Seam Rule

Slip-on seat covers are one of the most common sewing projects for a car: towelling covers for the beach or the gym, a washable cover for a work van, or a cover to hide a torn seat until it can be re-trimmed properly. They are simpler than a fitted re-trim because nothing is glued or hog-ringed to the seat. The cover slides over and ties or hooks underneath. This guide works out how much fabric to buy with the Upholstery Fabric Calculator and then deals with the one rule that decides whether you should sew a cover at all.

Check for a side airbag before you buy any fabric

Many front seats have a side airbag built into the outer side of the backrest. In a crash it inflates outwards through a tear seam, a line of stitching in the factory cover designed to split at a set force. A slip-on cover that wraps that side of the backrest puts an extra layer of fabric, with ordinary seams, between the airbag and the person it is meant to protect. It can slow, deflect or block the deployment.

Look for a label on the outer side of the backrest marked "SRS", "Airbag" or "Side airbag", and check the owner's handbook, which will usually say whether seat covers may be used at all. If the seat has a side airbag:

  • Do not sew a cover that wraps the backrest. A home-sewn cover cannot reproduce the specified tear seam, thread and stitch, and there is no way to test it.
  • If you want covers, buy ones the maker states are airbag-compatible for that specific seat. These have a matching tear seam on the airbag side.
  • Never cover, glue over or obstruct an airbag module, and do not tuck fabric into the gap where it deploys.
  • A cushion-only cover (the seat base) avoids the backrest, but check the handbook too: some passenger seats have an occupant-detection sensor in the cushion that decides whether the front airbag fires, and the maker may warn against thick covers there.

Rear benches in many cars have no seat-mounted airbags, which is why they are the safest place to start. Check anyway: some do.

Measuring for a slip-on cover

A slip-on cover for one front seat is made of a few large pieces. Measure each as a rectangle, over the curves with a soft tape, and include enough to wrap under the edges where the cover will tie:

PieceSize (cm)Area (m²)
Backrest front65 × 520.338
Backrest back65 × 520.338
Cushion top55 × 520.286
Cushion side skirts (two)55 × 150.165
Front apron52 × 150.078
Headrest sleeve (two faces)30 × 260.156

That is 1.36 m² for one seat and 2.72 m² for the pair. It is less than a full fitted re-trim, because a slip-on cover does not have separate bolsters and boxing strips; it simply drapes over them. On a seat with a side airbag, this is also the version you should not make.

How much to buy at three fabric widths

Enter the six areas for both seats, a 20% waste allowance for seams and the curved edges, and the width of the fabric. Home-sewing fabric often comes in about 1.1 m (43 inch), 1.37 m (54 inch) and 1.52 m (60 inch) widths:

Fabric widthLength (m)Length (yd)
1.10 m (43 in)2.973.25
1.37 m (54 in)2.382.61
1.52 m (60 in)2.152.35

The area with waste, 3.27 m² (35.2 ft²), is the same in every row. Only the width changes the length. On narrow fabric the length grows quickly, and a 65 cm backrest panel only fits one across a 1.1 m width, so narrow fabric also nests worse than the calculator assumes. Prefer the wider widths.

Towelling, velour and anything with a pile

Towelling (terry), velour, corduroy and many upholstery cloths have a pile or nap that looks different depending on which way you view it. Every piece has to be cut facing the same way, so the pieces cannot be turned to fit together on the fabric. Raise the allowance: at 35% the pair needs 2.68 m (2.93 yd) of 1.37 m fabric. Pre-wash towelling before cutting; cotton terry can shrink noticeably, and a cover that shrinks after its first wash will not go back on the seat.

A cushion cover for the rear bench

For a dog, a child's muddy boots or a work kit, a cover for the rear bench cushion alone is often all that is needed, and it keeps clear of seat belts on the backrest. A typical bench cushion with its front edge and two short ends is 0.93 m², which at 20% waste is 0.81 m (0.89 yd) of 1.37 m fabric. Leave openings for every seat-belt buckle and child-seat anchor, and make sure the cover cannot slide over them. For a full rear hammock that hooks to the front headrests, see dog crate or seat hammock.

What the calculator does not cover

  • Airbag compatibility. The calculator works out fabric. It cannot tell you whether a cover is safe on your seat; only the seat's labelling, the handbook and the cover maker's compatibility statement can.
  • Fasteners and elastic. Elastic, ties, hooks and any non-slip backing are separate purchases.
  • Pattern layout. The length assumes pieces nest perfectly. Lay paper patterns on a strip the width of your fabric before buying.
  • Fit. Seats vary even within one model (heated, electric, sports). Measure your own.

Fabric choice and other safety points

  • Fabric used in a vehicle interior should meet FMVSS 302 (the US flammability standard for vehicle interior materials) or the local equivalent. Dressmaking and furniture fabrics are not necessarily tested to it; some upholstery suppliers state the rating.
  • If you bond a foam or non-slip backing on with spray adhesive, do it outdoors or with strong ventilation, wear a respirator with organic-vapour cartridges, gloves and eye protection, and read the Safety Data Sheet. Let the solvent flash off fully before the cover goes in a closed car.
  • If fitting covers means removing a seat, remember the airbag, seat-belt pretensioner and sensor connectors underneath: disconnect the battery and wait as the service manual says, follow the manual, or have a professional do it. Slip-on covers should not need the seat removed.
  • A cover must never stop a seat belt from retracting or a buckle from latching.

Measured carefully, a pair of front covers from wide fabric is a two- to three-yard job. Run your own numbers in the Upholstery Fabric Calculator, but check the seat labels first. For seats with side airbags, the right answer is a certified compatible cover, not a sewing pattern. If you are re-covering properly rather than slipping a cover over, start with how much upholstery fabric to re-cover two front seats.

Get new guides by emailOccasional emails. No spam. Unsubscribe anytime.